Products

Main Products

  • Using an Oxy Acetylene Cutting Torch: Setting Up, …

    Another advantage of cutting off the oxygen supply first is that mini flashbacks are less likely to occur. Despite most cutting torches having protective features against it, flashbacks can still happen. Mini flashbacks occur in the form of a loud pop or bang. While generally considered harmless, mini flashbacks can still cause accidents.

  • Apprenticeships and traineeships | North Metropolitan TAFE

    Once you are booked into training your employer is obliged to release you; directing you back to work disadvantages you by delaying your training program. Whilst you should comply with the instructions from your employer, if you believe that your training is being delayed you can contact the Apprenticeship Management Team to discuss your concerns.

  • WORK SHOPPRACTICE LABORATORY MANUAL I/II Semester (WSL16/26)

    Students should follow the instructions given below to write the Lab Record Right Hand Page in the Record book 1. Serial number and Date of Experiment 2. Name of the Experiment 3. Aim of the Experiment 4. Tools required 5. Marking tools and cutting tools required 6. Procedures for preparation of model 7. Result obtained

  • BOC Guidelines for Welding and Cutting

    The oxy-acetylene flame produces an intense bright light that causes discomfort and possible injury to the eyes. In order to comfortably and safely see the flame when welding or cutting, welding goggles must be worn. various processes: Shade 4 – Oxy-cutting

  • Achiever Essays - Your favorite homework help service ...

    Achieveressays.com is the one place where you find help for all types of assignments. We write high quality term papers, sample essays, research papers, dissertations, thesis papers, assignments, book reviews, speeches, book reports, custom web content and business papers.

  • Join LiveJournal

    Password requirements: 6 to 30 characters long; ASCII characters only (characters found on a standard US keyboard); must contain at least 4 different symbols;

  • Diving cylinder - Wikipedia

    The pressure vessel is a seamless cylinder normally made of cold-extruded aluminium or forged steel. Filament wound composite cylinders are used in fire fighting breathing apparatus and oxygen first aid equipment because of their low weight, but are rarely used for diving, due to their high positive buoyancy.

  • Principal cutting process advantages and disadvantages - …

    Disadvantages. Oxy-fuel. Low capital cost. Primarily limited to mild and low alloy steels. No electrical requirements. Less suitable for stainless steels and aluminium. Consumable costs low. Wide HAZ.

  • Module 2 Thermal Processes - eCollege

    Disadvantages of Oxy-Acetylene Welding Oxy-acetylene weld lines are much rougher in appearance than other kinds of welds, and require more finishing if neatness is required.

  • The Procedure Of Oxyfuel Cutting | Basic Requirements …

    1/5/2020 · The temperature in order to preheat the metal effectively should be around 700 °C to 900 °C, preferably well below its melting point. This step then leads to an exothermic chemical reaction in between the oxygen, acetylene, and the metal where a jet of …

  • Oxy/Acetylene Welding

    Disadvantages of Oxy-Acetylene Welding : Oxy/Acetylene weld lines are much rougher in appearance than other kinds of welds, and require more finishing if neatness is required. Oxy/Acetylene welds have large heat affected zones (areas around the weld line that have had their mechanical properties adversely affected by the welding process).

  • Heavy Duty Cutting Kit Oxy-Acetylene - HSS

    Close the cutting torch’s acetylene valve, wait for the flame to go out, then close the oxygen valve (in that order). Close both cylinder valves and relieve the pressure in the system. Open the oxygen valves on the cutting torch and wait for the pressure to drop, then

  • Using an Oxy Acetylene Cutting Torch: Setting Up, …

    An oxy acetylene cutting torch allows oxygen to mix with acetylene to combust and produce a flame that has a temperature exceeding 3000 C. This kind of flame is the only one hot enough to cut through mild steel, specifically any kind of steel that only has a maximum of 0.3% carbon.

  • Safe Operating Procedure OXY ACETYLENE SET

    Turn off acetylene/fuel cylinder valve. Open acetylene/fuel blowpipe valve and release gas. When acetylene/fuel gauges read zero, release regulator adjusting knob. Close acetylene/fuel blowpipe valve. Hang up welding blowpipe and hoses. Turn off

  • Advantages And Disadvantages Of Flame Cutting - …

    14/12/2020 · The disadvantages of oxygen-propane flame cutting compared with oxygen-acetylene flame cutting: 1. The flame temperature is relatively low, and the cutting preheating time is slightly longer. 2. Oxygen consumption is also higher than oxygen-acetylene flame cutting, but the total cutting cost is much lower than oxygen-acetylene flame cutting.

  • (PDF) AN INTRODUCTION TO OXY/ACETYLENE WELDING …

    Lighting-Up Procedure To begin oxygen/acetylene welding or cutting, open the Fig. 1 Oxy/Acetylene Equipment cylinder valves slowly by means of the cylinder key (s). Do not open suddenly or there may be serious damage to the regulator and the possibility of an …

  • Construction Standards for Small Vessels (2010) - TP 1332 E

    3.3.3.1 Where a vessel is intended to operate more than 25 nautical miles from shore, windows, portlights, and skylights shall be mechanically fastened in place in accordance with the manufacturer's instructions.

  • Solution Essays - We get your assignments done...

    Get high-quality papers at affordable prices. With Solution Essays, you can get high-quality essays at a lower price. This might seem impossible but with our highly skilled professional writers all your custom essays, book reviews, research papers and other custom tasks you order with us will be of high quality.

  • Statistiques et évolution de l'épidémie de CoronaVirus ...

    Suivez l'évolution de l'épidémie de CoronaVirus / Covid19 dans le monde. Cas confirmés, mortalité, guérisons, toutes les statistiques

  • Oxy-Fuel Cutting with Propylene - Welding Tips and Tricks

    * acetylene prices are rising much faster than propylene * better heat transer properties than acetylene * no withdrawal rate limitations disadvantages * cant gas weld with it...too much pressure and too much flow rate to weld metal with any quality

  • Choosing Between Plasma Cutting and Oxy-fuel Systems

    19/3/2021 · Two popular metal-cutting processes are plasma arc and oxy-fuel cutting. Both systems have advantages and disadvantages, so determining the best fit depends on numerous factors, including the type and thickness of the metal being cut, location of …

  • What is the advantage in the welding process of oxy …

    2/4/2020 · Advantages of Oxy-Acetylene Welding : It's easy to learn. The equipment is cheaper than most other types of welding rigs (MIG/TIG welding) The equipment is more portable than most other types of welding rigs (MIG/TIG welding) Oxy/Acetylene equipment can also be used to "flame-cut" large pieces of material.

  • Designing MOF Nanoarchitectures for Electrochemical Water ...

    Among these, Co-based transition metal oxides and (oxy)hydroxides, particularly cobalt-based polymetallic compounds, [112, 208-213] are prominent owing to their unique 3d electronic configurations. Zhou et al. reported a facile strategy in which layered 2D MOFs were used as precursors to fabricate metal oxide/carbon (MO x /C, M = Co, Ni, and Cu ...